Bush Hog SQ160 Operator's Manual

ASSEMBLYll OPERATION ll MAINTENANCE04/09 Rev. 1 $4.0050056690SSqquueeaalleerr SSeerriieess RRoottaarryy CCuutttteerrssSSQQ114422,, SSQQ114488,,

8Figure 2-2H. Hold driveline sections parallel to each otherand check for minimum 6 inches (15cm) overlap.Figure 2-3). If driveline has been marke

AVOID PLACING HANDS, FEET OR ANYOTHER BODY PARTS BENEATH THE CUTTERWHILE MAKING HEIGHT ADJUSTMENTS.Each cutter can be adjusted to several cutting

ROTATING CUTTER BLADES, STAND CLEARUNTIL ALL MOION HAS STOPPED. TO AVOIDAN ACCIDENTAL FALL FROM TRACTORAND POSSIBLE INJURY FROM CUTTER, USEROPS (ROLLO

is 2.5 quarts (2.3L) for transfer and 1.5 quarts (1.4L)for outboard gearbox.7. Yoke( Figures 4-4 & 4-5) - Apply multi-purposegrease to fitting on

4-4 SHEAR BOLT REPLACEMENT(SQ142 & SQ148 - 1/2 x 3”, Gr. 2)A. Slide yoke shield back. (Figure 4-2)B. Realign holes in yoke and shaft and remove

4-9 BLADE HOLDER AND GEARBOXINSTALLATION (All Except SQ84T)A. Raise cutter and securely block into position.B. Attach gearbox to cutter deck using fla

TABLE 4-2 GENERAL TROUBLESHOOTINGPROBLEM PROBABLE CAUSE REMEDYUneven Cut Cutter not level side to side or Refer to SECTION II.front to rearWorn or ben

SECTION VDEALER ASSEMBLY15 5-1 ASSEMBLYA. Attach single-holed end of A-frame struts toholes in mounting brackets using 5/8” x 1-3/4” cap-screws, 5/8”

5-2 OPTIONAL FRONT SHIELDINGINSTALLATION (SQ142, SQ148, SQ160,SQ172, SQ184)A. Install front belting to deck lip angle securingwith 3/8 x 1-1/4”

5-6 SQ84T REAR BAND INSTALLATIONA. Fasten band to rear middle of deck using 3/8 x1” bolts, flatwashers, lockwashers and nuts in exist-ing holes. Lip a

CONGRATULATIONS!You have invested in the best implement of its type on the market today.The care you give your Bush Hog implement will greatly determi

SAFETY DECALSTo promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damagecan occur to safety decals either

TORQUE SPECIFICATIONSProper toque for American fasteners used on Bush Hog equipment.Recommended Torque in Foot Pounds (Newton Meters).*Proper torque f

20BUSH HOG SQUEALER SLIP CLUTCHESBush Hog Squealer Rotary Cutters are subject to having either “Bondioli &Pavesi / Binacchi” or “EG / Comer” slip

2501 Griffin Ave. llSelma, AL 36703Telephone (334) 874-2700 ll www.bushhog.com

SQUEALER ROTARY CUTTERSTABLE OF CONTENTSSECTION/PARA PAGEWarranty ...2Deal

LIMITED WARRANTYOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOBush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from anauthori

DEALER PREPARATION CHECK LISTSQUEALER ROTARY CUTTERSBEFORE DELIVERING MACHINE — The following check list should be completed.Use the Operator’s Manual

IMPORTANT SAFETY PRECAUTIONSThis symbol is used to call attention to safetyprecautions that should be followed by theoperator to avoid accidents. Wh

IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNINGEMPLOYERS, EMPLOYEES AND OPERATIONS.*(This section is intended to explain in broad terms the concept

SECTION IINTRODUCTION AND DESCRIPTION1-1 INTRODUCTIONWe are pleased to have you as a Bush Hog cus-tomer. Your Squealer Series Rotary Cutter has

7NOTEDue to the many variations in tractor / imple-ment hitch points and corresponding differ-ences in distances between tractor PTOshafts and implem